CameraSpecific class provides access to the camera scanner specific parameters.
Type - Java.Lang.Object
Properties
AimTimer
Duration in milliseconds for timed aim types ScannerConfig.AimType.TIMED_HOLD and ScannerConfig.AimType.TIMED_RELEASE. Note than this duration must be less than the beamTimer.
Type - System.Int32
AimType
Describes the type of aiming to use. Note: Setting aimType is recommended instead of ScannerConfig.ReaderParams.ReaderSpecific.ContinuousRead.isContinuousScan. If the application modifies ScannerConfig.ReaderParams.ReaderSpecific.ContinuousRead.isContinuousScan and aimType, the aimType settings will take precedence.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+AimType
BeamTimer
Sets the maximum amount of time that the reader remains on (0 - 60,000 ms in increments of 100 ms). A value of 0 sets the reader to stay on indefinitely.
Type - System.Int32
ContinuousRead
ContinuousRead class provides access to continuous scanning related parameters.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+ReaderParameters+ReaderSpecifics+ContinuousRead
DifferentSymbolTimeout
This setting is used to prevent the scanner from decoding another symbol within this time interval. This is applicable only for the aim type ScannerConfig.AimType.CONTINUOUS_READ. The user may want to prevent decoding too quickly and set an interval that the user can aim before decoding the next barcode. A value of 0 means no interval is required between two successive reads. Boundary values are 0 to 5000 in milliseconds in 500 increments such as 0, 500, 1000... etc
Type - System.Int32
IlluminationMode
Turns camera illumination on and off. This option is only available when camera is selected in the Barcode input Scanner selection option. Use class ScannerConfig.IlluminationMode.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+IlluminationMode
Inverse1DMode
This parameter allows the user to select decoding on inverse 1D bar codes. Use class ScannerConfig.Inverse1DMode.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+Inverse1DMode
LinearSecurityLevel
Sets the number of times a bar code is read to confirm an accurate decode. Use class ScannerConfig.LinearSecurityLevel..
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+LinearSecurityLevel
OneDQuietZoneLevel
This parameter sets the effort at which the decoder will attempt to decode margin-less barcodes. Behavior of the level set to this parameter will vary based on the margin-less decoder selected. Note: Higher margin-less levels will increase decoding times and the risk of decoding errors. Zebra therefore recommends enabling only the symbologies that require a higher margin-less level, and leaving all other symbologies at the default level of 1. Use enum ScannerConfig.OneDQuietZoneLevel.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+OneDQuietZoneLevel
PicklistEx
Allows the imager to decode only the barcode that is directly under the cross-hair/reticle (+) part of the pattern. This feature is useful in applications where multiple barcodes may appear in the field of view during a decode session and only one of them is targeted for decode. Use enum ScannerConfig.PicklistEx.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+PicklistEx
PoorQualityDecodeEffortLevel
This parameter permits selection of enhancement modes for decoding barcodes of poor or degraded quality. Use enum ScannerConfig.PoorQualityDecodeEffortLevel.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+PoorQualityDecodeEffortLevel
SameSymbolTimeout
This setting is used to prevent the scanner driver from decoding the same symbol within this time interval. This is applicable only for the aim type ScannerConfig.AimType.CONTINUOUS_READ. Basically in the continuous mode the user can perform rapid scan and to prevent the user from decoding the same barcode twice user can set this value to an appropriate interval (in milliseconds). A value of 0 means no interval is required between two successive reads. Boundary values are 0 to 5000 in milliseconds in 500 increments such as 0, 500, 1000... etc
Type - System.Int32
ViewfinderMode
Configures the Viewfinder modes supported for camera scanning. Use class ScannerConfig.ViewFinderMode.
Type - Symbol.XamarinEMDK.Barcode.ScannerConfig+ViewFinderMode
ViewfinderOffsetX
Sets the X Axis position of the top left corner of the view finder. The valid range is 0 to 100.
Type - System.Int32
ViewfinderOffsetY
Sets the Y Axis position of the top left corner of the view finder. The valid range is 0 to 100.
Type - System.Int32
ViewfinderSize
Sets the size of the view finder window in camera scanner. Default is 100, meaning it will show in full screen. As an example, if it is set to 50 View finder of half the full width and half the full height is used to show the preview. The valid range is 0 to 100.
Type - System.Int32