The "SmartDocs" bar can customize this page to show only the features present on a particular Zebra device.
OSX, MX and Android version information for a device can be found in the Android Settings panel or by querying the device through ADB, EMDK or the MX CSP. More info.
The Audio Volume UI Manager (AudioVolUIMgr) can add, delete and replace Audio Profiles, and can select an Audio Profile to be in effect on the device. It also allows administrators to modify the "Factory Preset" Audio Profile (which cannot be deleted), and to directly control the Mute and Vibrate states of the device, which are independent of all audio streams and Audio Profiles.
Many Zebra Android devices contain a Zebra Volume Control (ZVC), a UI component that allows a device user to easily adjust the volumes of various audio streams in the device. An audio stream is a channel through which audio can be generated and output to a speaker or headset. The number of audio streams supported by an Android device is generally fixed, but the number of possible purposes for which audio can be generated is theoretically unlimited. As a result, a particular audio stream might be used for a purpose other than that for which it was intended.
Note: The Zebra Volume Control component is included on most Zebra Android devices running KitKat and higher. It is enabled by default on all devices except those running Lollipop, on which it must be enabled manually. AudioVolUIMgr is supported only on devices that include the ZVC.
The standard Android Audio Volume Control UI identifies each audio stream that can be controlled in a fixed manner that is predefined for each audio stream. Such identification might not accurately reflect the purposes for which a given audio stream is being used. This can produce less than optimal user experiences since the device user might change the volume of an audio stream without realizing its affect on other systems.
The ZVC allows configuration of the manner in which audio Streams are identified to the device user, thus allowing the user experience to be customized. The ZVC also provides even more control over the user experience by allowing configuration of the minimum, maximum, and preset values for a given audio stream. For example, the minimum volume for an audio stream could be set as some value greater than zero to prevent a device user from turning it off completely and potentially missing important audio notifications that are performed on that audio stream.
The ZVC also provides support for Audio Profiles, which define different scenarios or use cases in which one or more audio streams can be used. Each Audio Profile can configure the behavior of ZVC for some or all of the available audio streams. By selecting a defined Audio Profile, the configuration of ZVC for multiple audio streams can be configured in a single operation. For example, there might be one Audio Profile for working in a quiet office and another for working in a noisy warehouse.
The ZVC can be invoked by pressing the volume control buttons on a device (when available) or by selecting the Sound -> Volumes screen from the Android Settings panel. The UI presented by the ZVC is based on the most recent configuration applied to ZVC using the AudioVolUIMgr, in particular the set of defined Audio Profiles and the currently selected Audio Profile.
The following audio streams are supported:
An Audio Profile can be defined to configure the following settings for any or all of the above audio streams:
An Audio Profile can configure the volume levels for each of four audio modes: Speaker, Receiver, Wired headset, and Bluetooth headset. The specified modes are determined based on the physical output path to which an audio stream is directed. For each mode, the following volume levels can be specified.
Note: The Zebra Volume Control component is included on most Zebra Android devices running KitKat and higher. It is enabled by default on all devices except those running Lollipop, on which it must be enabled manually. AudioVolUIMgr is supported only on devices that include the ZVC.
IMPORTANT:For some devices, Zebra Volume Control requires purchase of a Mobility DNA Enterprise License. About MDNA licensing.
Used to mute and unmute sounds on the device and enable the device to vibrate.
Parm Name: MuteVibrateState
| Option | Name | Description | Note | Requires |
|---|---|---|---|---|
| 0 | Do not change | This value (or the absence of this parm from the XML) causes no change to device settings; any previously selected setting is retained. |
OSX: 4.4+ MX: 4.4+ |
|
| 1 | Mute - Turn off audible sounds | Enables the global Mute state on the device, silencing the output of all audio streams. |
OSX: 4.4+ MX: 4.4+ |
|
| 2 | Vibrate - Turn off audible sounds and turn on vibrate | Enables the global Mute and Vibrate states on the device, silencing the output of all audio streams and enabling haptic feedback (vibrate). |
OSX: 4.4+ MX: 4.4+ |
|
| 3 | UnMute - Turn on audible sounds | Disables the global Mute and Vibrate states on the device to be disabled, enabling the output of all audio streams and disabling haptic feedback (vibrate). |
OSX: 4.4+ MX: 4.4+ |
Used to set a previously created Audio Profile or the Factory Preset Audio Profile to be the current Audio Profile. Also can be used to force the volumes of all audio streams back to the Preset volumes specified for the current Audio Profile.
Note: Since the configuration of the Factory Preset Audio Profile can be modified, resetting to the FactoryPreset profile (option 3) might not result in "Factory Defined" settings.
Parm Name: CurrentProfileAction
| Option | Name | Description | Note | Requires |
|---|---|---|---|---|
| 0 | Do nothing | This value (or the absence of this parm from the XML) causes no change to device settings; any previously selected setting is retained. |
OSX: 4.4+ MX: 4.4+ |
|
| 1 | Set an Audio UI Profile as the current Profile | Causes a previously created Audio Profile to be made the new current Audio Profile. |
OSX: 4.4+ MX: 4.4+ |
|
| 2 | Adjust to the Preset volume level of the current Profile | Causes the volume levels of all audio streams to be reset to the Preset volume levels configured for the current Audio Profile. |
OSX: 4.4+ MX: 4.4+ |
|
| 3 | Set the FactoryPreset Profile as the current Profile | Causes the Factory Preset Audio Profile to be the current Audio Profile. |
OSX: 4.4+ MX: 4.4+ |
Used to enter the name of an existing Audio Profile to be set as the new current Audio Profile. If the specified name does not match the name of a currently defined Audio Profile, an error will be returned in the Result XML document.
Parm value input rules:
Shown if: The Current Active Profile Action is "Set an Audio UI Profile as the current Profile"
Parm Name: CurrentProfileName
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to enter whether the current volume levels of all audio streams affected by the Audio Profile should be set to the Preset volume levels of that Audio Profile.
Shown if: The Current Active Profile Action is "Set an Audio UI Profile as the current Profile"
Parm Name: SetCurrentProfileOption
| Option | Name | Description | Note | Requires |
|---|---|---|---|---|
| 1 | Do not adjust the volume level | Causes the Preset volume levels specified for all audio streams in the new current Audio Profile to be ignored. If the current volume level of an audio stream is less than the minimum, it will be changed to the minimum and if the current volume level of an audio stream is greater than the minimum, then it will be changed to the maximum. Otherwise, the current volume level of an audio stream will be unchanged. |
OSX: 4.4+ MX: 4.4+ |
|
| 2 | Adjust the volume level | Causes the Preset volume levels specified for all audio streams in the new Audio Profile to be made the current volume levels for those audio streams. This option ensures that a specific set of volumes will be in effect after setting a new current Audio Profile. This should be used with caution since it could have a noticeable impact on current or future audio output. |
OSX: 4.4+ MX: 4.4+ |
Used to create a new Audio Profile, modify the "FactoryPreset" Audio Profile or modify or delete an existing Audio Profile. If an Audio Profile with the specified name exists in the device, it will be replaced by the newly defined one. If an Audio Profile with the specified name does not exist in the device, an error will be returned in the Result XML document.
Note: The "Remove an Audio UI Profile" feature (option 2) works only on inactive Profiles.
Parm Name: UIProfileAction
| Option | Name | Description | Note | Requires |
|---|---|---|---|---|
| 0 | Do nothing | This value (or the absence of this parm from the XML) causes no change to device settings; any previously selected setting is retained. |
OSX: 4.4+ MX: 4.4+ |
|
| 1 | Add an Audio UI Profile | Causes a new Audio Profile to be created, or an existing Audio Profile or the Factory Preset Audio Profile to be modified. |
OSX: 4.4+ MX: 4.4+ |
|
| 2 | Remove an Audio UI Profile | Deletes the named Audio Profile (must not be an active Profile). |
OSX: 4.4+ MX: 4.4+ |
Used to enter the name of the Audio Profile to Create, Modify or Delete. Speciied name must match exactly the name specified when setting the current Audio Profile using the CurrentProfileName parameter.
Note: This value cannot be "FactoryPreset" since this is a reserved name for the FactoryPreset Profile built into the device.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile" or "Remove an Audio UI Profile"
Parm Name: ProfileName
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that the ZVC will display to visually identify the audio stream that is typically used for music playback.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the audio stream that is typically used for music playback. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), or if the value provided does not reference an icon file, then no customized icon will be specified for the audio stream. This will cause ZVC to display the default icon defined for the audio stream.
Parm value input rules:
Shown if: he Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the user to view and modify the volume settings for the audio stream that is typically used for music playback. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for music playback when the device is in speaker mode. Valid range for music playback stream is 0–15 (0=inaudible; 15=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the music volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for music playback to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for music playback when the device is in receiver mode. Valid range for this stream is 0–15 (0=inaudible; 15=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the music volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for music playback to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for music playback when the device is in wired headset mode. Valid range for this stream is 0–15 (0=inaudible; 15=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the music volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for music playback to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for music playback when the device is in Bluetooth headset mode mode. Valid range for this stream is 0–15 (0=inaudible; 15=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the music volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for music playback to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_MUSIC_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that the ZVC will display to visually identify the audio stream that is typically used for the incoming call notification.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the audio stream that is typically used for the incoming call notification. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), or if the value provided does not reference an icon file, then no customized icon will be specified for the audio stream. This will cause ZVC to display the default icon defined for the audio stream.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the device user to view and modify the volume settings for the audio stream that is typically used for the typically used for the incoming call notification. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for the incoming call notification when the device is in speaker mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the ring tone volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for the incoming call notification to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for the incoming call notification when the device is in receiver mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the ring tone volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for the incoming call notification to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for the incoming call notification when the device is in wired headset mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the ring tone volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for the incoming call notification to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for the incoming call notification when the device is in Bluetooth headset mode mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the ring tone volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for the incoming call notification to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_RING_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that the ZVC will display to visually identify the audio stream that is typically used for other notifications.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the audio stream that is typically used for other notifications. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the device user to view and modify the volume settings for the audio stream that is typically used for other notifications. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for other notifications when the device is in speaker mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the notification volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for other notifications to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for other notifications when the device is in receiver mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the notification volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for other notifications to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for other notifications when the device is in wired headset mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the notification volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for other notifications to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for other notifications when the device is in Bluetooth headset mode mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the notification volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for other notifications to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_NOTIFICATION_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that the ZVC will display to visually identify the audio stream that is typically used by system sounds.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the audio stream that is typically used by system sounds. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), or if the value provided does not reference an icon file, then no customized icon will be specified for the audio stream. This will cause ZVC to display the default icon defined for the audio stream.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the device user to view and modify the volume settings for the audio stream that is typically used by system sounds. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used by system sounds when the device is in speaker mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the system volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used by system sounds to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used by system sounds when the device is in receiver mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the system volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used by system sounds to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used by system sounds when the device is in wired headset mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the system volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used by system sounds to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used by system sounds when the device is in Bluetooth headset mode mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the system volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used by system sounds to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_SYSTEM_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that the ZVC will display to visually identify the audio stream that is typically used for alarms.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the audio stream that is typically used for alarms. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), or if the value provided does not reference an icon file, then no customized icon will be specified for the audio stream. This will cause ZVC to display the default icon defined for the audio stream.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the device user to view and modify the volume settings for the audio stream that is typically used for alarms. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for alarms when the device is in speaker mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the alarm volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for alarms to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for alarms when the device is in wired headset mode. The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the system volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for alarms to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for alarms when the device is in receiver mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the alarm volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for alarms to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for alarms when the device is in Bluetooth headset mode mode. Valid range for this stream is 0–7 (0=inaudible; 7=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the system volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for alarms to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_ALARM_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that the ZVC will display to visually identify the audio stream that is typically used for phone calls.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the audio stream that is typically used for phone calls. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), or if the value provided does not reference an icon file, then no customized icon will be specified for the audio stream. This will cause ZVC to display the default icon defined for the audio stream.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the device user to view and modify the volume settings for the audio stream that is typically used for phone calls. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for phone calls when the device is in speaker mode. Valid range for this stream is 1–5 (1=lowest; 5=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the voice call volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for phone calls to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for phone calls when the device is in receiver mode. Valid range for this stream is 1–5 (1=lowest; 5=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the voice call volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for phone calls to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for phone calls when the device is in wired headset mode. Valid range for this stream is 1–5 (1=lowest; 5=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the voice call volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for phone calls to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the audio stream that is typically used for phone calls when the device is in Bluetooth headset mode mode. Valid range for this stream is 1–5 (1=lowest; 5=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the voice call volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the audio stream that is typically used for phone calls to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VOICECALL_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized label that ZVC displays to visually identify the decode beep virtual volume stream.
Note: If the value of this parm is empty (a length of 0), no customized label is created for the Audio Stream and the default label is displayed.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_Label
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a customized icon that the ZVC will display to visually identify the decode beep virtual volume stream. If specified, the value must be the full path and file name of an icon file in PNG format that resides in the device file system. An icon size of 48x48 pixels is recommended.
Note: If the value of this parm is empty (a length of 0), or if the value provided does not reference an icon file, then no customized icon will be specified for the audio stream. This will cause ZVC to display the default icon defined for the audio stream.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_Icon
Requires:
- OSX: 4.4+
- MX: 4.4+
Controls whether the ZVC allows the device user to view and modify the volume settings for the decode beep virtual volume stream. Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to this audio stream's visibility.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_Ctrl
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the decode beep virtual stream when the device is in speaker mode. Valid range for this stream is 0–10 (0=inaudible; 10=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the decode beep virtual volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the decode beep virtual stream to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_SPK_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the decode beep virtual stream when the device is in receiver mode. Valid range for this stream is 0–10 (0=inaudible; 10=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the decode beep virtual volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the decode beep virtual stream to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_RCVR_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the decode beep virtual stream when the device is in wired headset mode. The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the decode beep virtual volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the decode beep virtual stream to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_WHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set the minimum, maximum, and preset volume levels for the decode beep virtual stream when the device is in Bluetooth headset mode mode. Valid range for this stream is 0–10 (0=inaudible; 10=max). The user will not be able to lower or raise the volume outside of the minimum/maximum range that is set. If the decode beep virtual volume level was outside of this range at the time that this range is set, then the volume of this stream will be equal to the minimum or maximum level depending on whether it was below or above this volume range.
The preset volume level is a third volume level that must be greater than or equal to the minimum volume level and less than or equal to the maximum volume level. If the preset volume is outside of the minimum/maximum range, then this value will be be equal to the minimum or maximum level depending on whether it was below or above this volume range. This will be used by the SetCurrentProfileOption feature to adjust the volume of the decode beep virtual stream to this set level.
Entering an empty (length of zero) value (or the absence of this parm from the XML) will cause no change to the volume levels.
Parm value input rules:
Shown if: The Audio UI Profile Action is "Add an Audio UI Profile"
Parm Name: STREAM_VVS_BTHS_LEVEL
Requires:
- OSX: 4.4+
- MX: 4.4+
Used to set a custom label that the ZVC displays to identify the tone used to indicate audible keypad feedback. Note: If the value of this parameter is empty (a length of 0), no customized label is created for the keypad tone and the default label is displayed.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_Label
Requires:
- MX: 10.2+
Used to set a custom icon that the ZVC displays to identify the stream used for keypad feedback. If specified, the value must be the full path and file name of an icon file in .PNG format that resides in the device file system. Zebra recommends an icon size of 48x48 pixels.
Note: If the value of this parameter is empty (a length of 0), or if the value provided does not reference an icon file, ZVC displays the default icon defined for the stream.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_Icon
Requires:
- MX: 10.2+
Controls whether the ZVC allows the device user to view and modify the settings for the keypad tone typically used to indicate a key-press. Entering an empty (length of zero) value (or the absence of this parameter from the XML) causes no change to this setting.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_Ctrl
Requires:
- MX: 10.2+
Used to set the minimum, maximum, and preset volume levels for the audio stream used for keypad feedback when the device is in speaker mode. Valid range for this stream is 0–4 (0=off; 4=max), with values separated by commas. The device user cannot reduce or increase the volume outside of the set minimum/maximum range. Entering an empty (length of zero) value (or the absence of this parm from the XML) causes no change to the volume levels.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_SPK_LEVEL
Requires:
- MX: 10.2+
Used to set the minimum, maximum, and preset volume levels for the audio stream used for keypad feedback when the device is in receiver mode. Valid range for this stream is 0–4 (0=off; 4=max), with values separated by commas. The device user cannot reduce or increase the volume outside of the set minimum/maximum range. Entering an empty (length of zero) value (or the absence of this parm from the XML) causes no change to the volume levels.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_RCVR_LEVEL
Requires:
- MX: 10.2+
Used to set the minimum, maximum, and preset volume levels for the audio stream used for keypad feedback when the device is in wired headset mode. Valid range for this stream is 0–4 (0=off; 4=max), with values separated by commas. The device user cannot reduce or increase the volume outside of the set minimum/maximum range. Entering an empty (length of zero) value (or the absence of this parm from the XML) causes no change to the volume levels.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_WHS_LEVEL
Requires:
- MX: 10.2+
Used to set the minimum, maximum, and preset volume levels for the audio stream used for keypad feedback when the device is in Bluetooth headset mode. Valid range for this stream is 0–4 (0=off; 4=max), with values separated by commas. The device user cannot reduce or increase the volume outside of the set minimum/maximum range. Entering an empty (length of zero) value (or the absence of this parm from the XML) causes no change to the volume levels.
Parm value input rules:
Parm Name: STREAM_KEYPADTONE_BTHS_LEVEL
Requires:
- MX: 10.2+
<wap-provisioningdoc>
<characteristic type="AudioVolUIMgr" version="4.4" >
<parm name="UIProfileAction" value="1"/>
<characteristic type="UIProfile">
<parm name="ProfileName" value="Test2"/>
<characteristic type="UIProfile-streamconfig">
<parm name="STREAM_MUSIC_Label" value="MUSIC"/>
<parm name="STREAM_MUSIC_Icon" value="/internal/xmltest/in/Speaker.png"/>
<parm name="STREAM_MUSIC_Ctrl" value="1"/>
<parm name="STREAM_MUSIC_SPK_LEVEL" value="1,14,8"/>
<parm name="STREAM_MUSIC_RCVR_LEVEL" value="2,13,8"/>
<parm name="STREAM_MUSIC_WHS_LEVEL" value="3,12,8"/>
<parm name="STREAM_MUSIC_BTHS_LEVEL" value="4,11,8"/>
<parm name="STREAM_RING_Label" value="RING"/>
<parm name="STREAM_RING_Icon" value="/internal/xmltest/in/Ring.png"/>
<parm name="STREAM_RING_Ctrl" value="1"/>
<parm name="STREAM_RING_SPK_LEVEL" value="1,7,5"/>
<parm name="STREAM_RING_RCVR_LEVEL" value="3,7,5"/>
<parm name="STREAM_RING_WHS_LEVEL" value="3,7,5"/>
<parm name="STREAM_RING_BTHS_LEVEL" value="4,7,5"/>
<parm name="STREAM_NOTIFICATION_Label" value="NOTIFY"/>
<parm name="STREAM_NOTIFICATION_Icon" value="/internal/xmltest/in/Notify.png"/>
<parm name="STREAM_NOTIFICATION_Ctrl" value="1"/>
<parm name="STREAM_NOTIFICATION_SPK_LEVEL" value="1,7,5"/>
<parm name="STREAM_NOTIFICATION_RCVR_LEVEL" value="3,7,5"/>
<parm name="STREAM_NOTIFICATION_WHS_LEVEL" value="3,7,5"/>
<parm name="STREAM_NOTIFICATION_BTHS_LEVEL" value="4,7,5"/>
<parm name="STREAM_SYSTEM_Label" value="SYSTEM"/>
<parm name="STREAM_SYSTEM_Icon" value="/internal/xmltest/in/System.png"/>
<parm name="STREAM_SYSTEM_Ctrl" value="1"/>
<parm name="STREAM_SYSTEM_SPK_LEVEL" value="1,7,5"/>
<parm name="STREAM_SYSTEM_RCVR_LEVEL" value="1,7,5"/>
<parm name="STREAM_SYSTEM_WHS_LEVEL" value="1,7,5"/>
<parm name="STREAM_SYSTEM_BTHS_LEVEL" value="4,7,5"/>
<parm name="STREAM_ALARM_Label" value="ALARM"/>
<parm name="STREAM_ALARM_Icon" value="/internal/xmltest/in/ALARM.png"/>
<parm name="STREAM_ALARM_Ctrl" value="1"/>
<parm name="STREAM_ALARM_SPK_LEVEL" value="1,7,4"/>
<parm name="STREAM_ALARM_RCVR_LEVEL" value="1,7,4"/>
<parm name="STREAM_ALARM_WHS_LEVEL" value="1,7,4"/>
<parm name="STREAM_ALARM_BTHS_LEVEL" value="1,7,4"/>
<parm name="STREAM_VOICECALL_Label" value="PHONE"/>
<parm name="STREAM_VOICECALL_Icon" value="/internal/xmltest/in/Phone.png"/>
<parm name="STREAM_VOICECALL_Ctrl" value="1"/>
<parm name="STREAM_VOICECALL_SPK_LEVEL" value="1,5,3"/>
<parm name="STREAM_VOICECALL_RCVR_LEVEL" value="1,5,3"/>
<parm name="STREAM_VOICECALL_WHS_LEVEL" value="1,5,3"/>
<parm name="STREAM_VOICECALL_BTHS_LEVEL" value="1,5,3"/>
<parm name="STREAM_VVS_Label" value="SCAN"/>
<parm name="STREAM_VVS_Icon" value="/internal/xmltest/in/ScanGun.png"/>
<parm name="STREAM_VVS_Ctrl" value="1"/>
<parm name="STREAM_VVS_SPK_LEVEL" value="2,10,8"/>
<parm name="STREAM_VVS_RCVR_LEVEL" value="2,10,8"/>
<parm name="STREAM_VVS_WHS_LEVEL" value="2,10,8"/>
<parm name="STREAM_VVS_BTHS_LEVEL" value="2,10,8"/>
</characteristic>
</characteristic>
</characteristic>
</wap-provisioningdoc>